Page History

...

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives -

...

PASS

This test case will test point to point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

PASS
2000.2 IPV4: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

PASS
2000.3 IPV4_2: Add point intents between h1 and h9 - PASS
2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP 2000.3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

PASS
2000.6 DUALSTACK1 2000.4 SDNIP-ICMP: Add point intents between h1 h3 and h9 h11 - PASS
2000.5 SDNIP-TCP7 VLAN: Add point intents between h1 h5 and h9 h21 - PASS
2000.6 DUALSTACK18 VLAN: Add point intents between h3 h5 and h11 h21 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install Intent State Passed
Bandwidth Allocation check Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

PASS

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

...

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - FAIL

Assertion results for IPV4 multi to single with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved FailedReceived Passed
Remove Intents FailedAfter removing intents Flow State Passed

6000.3 NOOPTION: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with no options set
After removing intents Flow State Passed

6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL

Assertion results for IPV4 single to multi point intent with partial failures allowed
After removing intents Flow State Passed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 10: Start Mininet topology with OF 1.0 switches - PASS

Start mininet topology with OF 1.0 switches to test intents, exits out if topology did not start correctly

10.1 Starting Mininet topology with OF 1.0 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.0 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - FAIL

Assertion Result for VLAN Encapsulated host intent
Install Intent State Passed
Encapsulation intents check Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Pingall Failed
Remove Intents PassedAfter removing intents Flow State Passed

1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

This test case will test point to point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Passed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents FailedAfter removing intents Flow State Passed

6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL

Assertion results for IPV4 single to multi point intent with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Failed
Isolation link Down Passed
Partial failure isolation link Down Intent State Failed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Failed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Failed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed
Remove Intents FailedAfter removing intents Flow State Passed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 10: Start Mininet topology with OF 1.0 switches - PASS

Start mininet topology with OF 1.0 switches to test intents, exits out if topology did not start correctly

10.1 Starting Mininet topology with OF 1.0 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.0 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

This test case will test point to point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intent

2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed
Remove Intents PassedAfter removing intents Flow State Passed

2000.2 IPV4: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Failed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed
Remove Intents PassedAfter removing intents Flow State Passed

2000.3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - FAIL

Assertion Result for SDNIP-ICMP IPV4 using TCP point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.5 SDNIP-TCP2 IPV4: Add point intents between h1 and h9 - FAIL

Assertion Result for SDNIP-TCP IPV4 using ICMP point intents
Initial Iperf Failed
Remove Intents Passed

2000.6 DUALSTACK1: Add point intents between h3 and h11 - FAIL

point intent
Assertion Result for Dualstack1 IPV4 with mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.7 VLAN3 IPV4_2: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intents
Install VLAN Encapsulation Point IntentInstall Intent State Passed
Encapsulation intents check failed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping FailedPassed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved FailedReceived Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add 11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intentInstall VLAN Encapsulation Point IntentInstall Intent State Passed
Bandwidth Allocation Encapsulation intents check FailedPassed
After removing intents Flow State Passed

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

...

Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install Intent State Passed
Bandwidth Allocation check Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

4000 3000.1 NOOPTION: Add multi Install and test single point to single multi point intents - PASS 4000
3000.2 IPV4: Add multi Install and test single point to single multi point intents - PASS
4000 3000.3 IPV4_2: Add multi single point to single multi point intents - PASS
4000 3000.4 VLAN: Add multi single point to single multi point intents - PASS 4000
3000.5 VLAN: Add multi single point to single point intents - PASS 4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case

...

4000:

...

Multi To Single Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.0 OVS running in Mininet and compile intents using Flow Objectives

4000.1 NOOPTION: Add multi point to single point intents 5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000 4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.0 - Using Flow Objectives -

...

FAIL

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - PASS
6000.3 NOOPTION: Install and test single point to multi point intents - PASS
FAIL

Assertion results for IPV4 multi to single

6000.4 NOOPTION: Install and test single point to multi point intents

with partial failures allowed

- PASS

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

Set up ONOS with 1 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 1000: Host Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case tests Host intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test point to point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

2000.1 NOOPTION: Add point intents between h1 and h9 - PASS
2000.2 IPV4: Add point intents between h1 and h9 - PASS
2000.3 IPV4_2: Add point intents between h1 and h9 - PASS
2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - PASS

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - FAIL

Assertion results for VLAN Encapsulation multi to single point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

Case 5000: Test host mobility with host intents - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - FAIL

Assert result for IPV4 host intent between h1, moved, and h9
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Pingall Passed
Remove Intents PassedAfter removing intents Flow State Failed

Case 6000: Test Multi to Single End Point Failure - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

6000.1 Installing Multi to Single Point intents with no options set - FAIL

Assertion results for IPV4 multi to single point intent end point failure with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Failed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

6000.2 Installing Multi to Single Point intents with partial failure allowed - FAIL

Assertion results for IPV4 multi to single with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Failed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

6000.3 NOOPTION: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Failed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL

Assertion results for IPV4 single to multi point intent with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Failed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test point to point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

2000.1 NOOPTION: Add point intents between h1 and h9 - PASS
2000.2 IPV4: Add point intents between h1 and h9 - PASS
2000.3 IPV4_2: Add point intents between h1 and h9 - PASS
2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - PASS

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Failed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed
Remove Intents FailedAfter removing intents Flow State Passed

6000.3 NOOPTION: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Passed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents FailedAfter removing intents Flow State Passed

6000.4
6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - PASS
6000.3 NOOPTION: Install and test single point to multi point intents - PASS 6000.4 NOOPTION: Install and test single point with partial failures allowed - FAIL

Assertion results for IPV4 single to multi point

intents

intent with partial failures allowed

- PASS

After removing intents Flow State Passed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

Set up ONOS with 1 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches 3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case

...

16:

...

Balance mastership of switches

...

- PASS

Assign OF 1.3 switches to ONOS nodes

12 16.1 Assigning Balancing mastership of switches to controllers - PASS

Case

...

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

...

1000: Host Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case tests Host intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow

...

Rules -

...

FAIL

This test case tests Host will test point to point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow ObjectivesRules

1000 2000.1 IPV4NOOPTION: Add host point intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

This test case will test point to point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

FAIL

Assertion Result for NOOPTION point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.2 IPV4: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP 2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intentSDNIP-ICMP IPV4 using TCP point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State PassedFailed
Link Down Topology State Passed
Link Down Pingall FailedPassed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.2 IPV45 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - FAIL

Assertion Result for Dualstack1 IPV4 with mac address point intentintents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State PassedFailed
Link Down Topology State Passed
Link Down Pingall FailedPassed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for 3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intentsBANDWIDTH ALLOCATION for point intent
Install Intent State Passed
Bandwidth Allocation check Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State PassedFailed
Link Down Topology State Passed
Link Down Pingall FailedPassed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install Intent State Passed
Bandwidth Allocation check Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

...

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 1 NODE(S) - OF 1.3 - Using Flow

...

Rules - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - PASS
6000.3 3000.1 NOOPTION: Install and test single point to multi point intents - PASS 3000
6000.2 IPV44 NOOPTION: Install and test single point to multi point intents with partial failures allowed - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 1 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 1 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - FAIL

Assertion results for IPV4 multi to single with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents FailedAfter removing intents Flow State Passed

6000.3 NOOPTION: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with no options set
After removing intents Flow State Passed

6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL

Assertion results for IPV4 single to multi point intent with partial failures allowed
After removing intents Flow State Passed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

...

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test point to point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

2000.1 NOOPTION: Add point intents between h1 and h9 - PASS
2000.2 IPV4: Add point intents between h1 and h9 - PASS
2000.3 IPV4_2: Add point intents between h1 and h9 - PASS
2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - PASS

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Rules

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.3 - Using Flow

...

Rules -

...

PASS

5000.1 Testing host mobility by moving h1 from s5 to s6

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP 5000.2 IPV4: Add host intents between h1 and h3 h9 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - FAIL

Assertion Result vlan IPV4
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Topology State Passed
Link Up Pingall Passed
Remove Intents PassedAfter removing intents Flow State Failed

1000.6 VLAN2: Add vlan host intents between h4 and h13 - FAIL

Assertion Result vlan IPV4
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Pingall Passed
Remove Intents PassedAfter removing intents Flow State Failed

1000.7 Encapsulation: Add host intents between h1 and h9 - FAIL

Assertion Result for VLAN Encapsulated host intent
Install Intent State Passed
Encapsulation intents check failed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Pingall Passed
Remove Intents PassedAfter removing intents Flow State Failed

1000.8 Confirm that ONOS leadership is unchanged - PASS

...

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - PASS
6000.3 NOOPTION: Install and test single point to multi point intents - PASS
6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - PASS

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

Set up ONOS with 1 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

Case 1000: Host Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Objectives -

...

PASS

This test case will test point to point tests Host intents using 3 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectivesand compile intents using Flow Objectives

1000.1 IPV4: Add host
2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.2 IPV4: Add point intents between h1 and h9 - FAIL PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

This test case will test point to point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

2000.1 NOOPTION: Add point intents between h1 and h9 - FAIL

Assertion Result for NOOPTION point intent

Assertion Result for IPV4 point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion Result for IPV4 no mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Failed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - FAIL

Assertion Result for SDNIP-ICMP IPV4 using TCP point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - FAIL

Assertion Result for Dualstack1 IPV4 with mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.7 VLAN: Add point intents between h5 and h21 - FAIL

Assertion Result for VLAN IPV4 with mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State FailedPassed

2000.8 VLAN2 IPV4: Add point intents between h5 h1 and h21 h9 - FAIL

Assertion Result for VLAN IPV4 point intents with VLAN treatmentintent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State FailedPassed

2000.9 1HOP3 IPV4_2: Add point intents between h1 and h3 h9 - FAIL

Assertion Result for 1HOP IPV4 with no mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed

Remove Intents PassedAfter removing intents Flow State Failed

Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install for VLAN Encapsulation Point IntentInstall Intent State Passed
Encapsulation intents Bandwidth Allocation check failedPassed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install Intent State PassedBandwidth Allocation check Failed
After removing intents Flow State Failed

Case 3000: Single to Multi Point Intents Test -

...

1 NODE(S) - OF 1.3 - Using Flow Objectives -

...

PASS

This test case will test single point to multi point intents using 3 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

3000.1 NOOPTION: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add 3000.2 IPV4: Install and test single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with IPV4 type and MAC addresses
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN 3000.3 IPV4_2: Add single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with IPV4 type and no MAC addresses
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed
After removing intents Flow State Failed

3000.4 VLAN: Add single point to multi point intents - FAIL

Assertion results for IPV4 single to multi point intent with IPV4 type and MAC addresses in the same VLAN
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

3000.5 VLAN: Add single point to multi point intents - FAIL

Assertion results for single to multi point intent with VLAN treatment
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

...

- PASS

Case 4000: Multi To Single Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 1 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 1 NODE(S) - OF 1.3 - Using Flow Objectives -

...

PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 1 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed -

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

4000.1 NOOPTION: Add multi point to single point intents - FAIL

Assertion results for NOOPTION IPV4 multi to single point intentwith partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Bad Sender Ping Passed
Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Bad Recipient Ping Passed
Link Down Topology State Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Link Down Pingall Passed
Link Up Passed
Link Up Intent State PassedFailed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received PassedRecieved Failed
Remove Intents PassedAfter FailedAfter removing intents Flow State FailedPassed

4000 6000.2 IPV4: Add multi 3 NOOPTION: Install and test single point to single multi point intents - FAIL

Assertion results for IPV4 single to multi to single point intent with IPV4 type and MAC addressesno options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Bad Sender Ping Passed
Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Bad Recipient Ping Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Passed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Down Flow State FailedLink Down Topology State Up Passed
Link Down Pingall Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter FailedAfter removing intents Flow State FailedPassed

4000.3 IPV4_2: Add multi point to single point intents 6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL

Assertion results for IPV4 single to multi to single point intent with IPV4 type and no MAC addressespartial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Passed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Passed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Passed
Partial failure isolation link Down Flow State Passed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter FailedAfter removing intents Flow State Failed

4000.4 VLAN: Add multi point to single point intents - FAIL

Assertion results for IPV4 multi to single point intent with IPV4 type and no MAC addresses in the same VLAN
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

4000.5 VLAN: Add multi point to single point intents - FAIL

Assertion results for multi to single point intent with VLAN ID treatment
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

4000.6 ENCAPSULATION: Add multi point to single point intents - FAIL

Assertion results for VLAN Encapsulation multi to single point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Ping Passed
Bad Sender Ping Passed
Bad Recipient Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Pingall Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

...

Passed

Case 18: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

18.1 Stopping and Removing Scapy Host Components - PASS
18.2 Stopping Mininet - PASS

Case 19: Copy karaf logs - PASS

Copying the karaf logs to preserve them throughreinstalling ONOS

19.1 Copying karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Set up ONOS with 3 node(s) ONOS cluster

2.1 Apply cell to environment - PASS
2.2 Uninstalling Atomix - PASS
2.3 Uninstalling ONOS package - PASS
2.4 Creating ONOS package - PASS
2.5 Installing Atomix - PASS
2.6 Installing ONOS package - PASS
2.7 Set up ONOS secure SSH - PASS
2.8 Checking ONOS service - PASS
2.9 Starting ONOS CLI sessions - PASS
2.10 Checking ONOS nodes - PASS
2.11 Checking ONOS applications - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Start mininet topology with OF 1.3 switches to test intents, exits out if topology did not start correctly

11.1 Starting Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Assign OF 1.3 switches to ONOS nodes

12.1 Assigning switches to controllers - PASS

Case 13: Create scapy components - PASS

13.1 Create scapy components - No Result
13.2 Start scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

15.1 Send packets from each host to the first host and confirm onos discovery - PASS
15.2 Populate hostsData - PASS

Case 16: Balance mastership of switches - PASS

16.1 Balancing mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

17.1 Enabling Flow Objectives - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

This test case tests Host intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

1000.1 IPV4: Add host intents between h1 and h9 - PASS
1000.2 DUALSTACK1: Add host intents between h3 and h11 - PASS
1000.3 DUALSTACK2: Add host intents between h1 and h11 - PASS
1000.4 1HOP: Add host intents between h1 and h3 - PASS
1000.5 VLAN1: Add vlan host intents between h4 and h12 - PASS
1000.6 VLAN2: Add vlan host intents between h4 and h13 - PASS
1000.7 Encapsulation: Add host intents between h1 and h9 - PASS
1000.8 Confirm that ONOS leadership is unchanged - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

This test case will test point to point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

2000.1 NOOPTION: Add point
5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - FAIL

Assert result for IPV4 host intent between h1, moved, and h9 Assertion Result for NOOPTION point intent
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Initial Flow State FailedPassed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State FailedPassed
Link Down Topology State Passed
Link Down Pingall PassedFailed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Pingall Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.3 - Using Flow Objectives - FAIL

Passed

2000.2 IPV4: Add point intents between h1 and h9 6000.1 Installing Multi to Single Point intents with no options set - FAIL

Assertion results Result for IPV4 multi to single point intent end point failure with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Passed
Initial Link Down Intent State PassedLink Down
Initial Flow State FailedLink Down Topology State Passed
Initial Ping Passed
Link Down Connectivity Check PassedIsolation link Down Passed
Isolation link Link Down Intent State PassedIsolation link
Link Down Flow State FailedPassed
Isolation link Link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check PassedLink Down Pingall Failed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State FailedPassed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State FailedPassed

6000 2000.2 Installing Multi to Single Point intents with partial failure allowed 3 IPV4_2: Add point intents between h1 and h9 - FAIL

Assertion results Result for IPV4 multi to single with partial failures allowedno mac address point intents
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Partial failure isolation link Down Intent State PassedPartial failure isolation link
Link Down Flow State Passed
Link FailedPartial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check PassedLink Down Pingall Failed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Passed
Link Up Intent Topology State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

6000.3 NOOPTION: Install and test single point to multi point intents - FAIL

Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

2000.4 SDNIP-ICMP: Add point intents between h1 and h9 - PASS
2000.5 SDNIP-TCP: Add point intents between h1 and h9 - PASS
2000.6 DUALSTACK1: Add point intents between h3 and h11 - PASS
2000.7 VLAN: Add point intents between h5 and h21 - PASS
2000.8 VLAN: Add point intents between h5 and h21 - PASS
2000.9 1HOP: Add point intents between h1 and h3 - PASS
2000.10 Add point to point intents using VLAN Encapsulation - PASS
2000.11 BANDWIDTH ALLOCATION: Checking bandwidth allocation for point intents between h1 and h9 - FAIL

Assertion Result for BANDWIDTH ALLOCATION for point intent
Install Intent State Passed
Bandwidth Allocation check
Assertion results for IPV4 single to multi point intent with no options set
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Initial Flow State Passed
Initial Ping Passed
Link Down Passed
Link Down Intent State Passed
Intial Link Down Flow State FailedInitial Connectivity Check Passed
Link Down Topology State Passed
Link Down Pingall Failed
Link Up Passed
Link Down Up Intent State Passed
Link Down Up Flow State FailedPassed
Link Down Up Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Isolation link Down Intent State Passed
Isolation link Down Flow State Failed
Isolation link Down Topology State Passed
Isolation link Down Connectivity Check Passed
Isolation link Down Connectivity Check Passed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Passed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Failed

6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - FAIL
Assertion results for IPV4 single to multi point intent with partial failures allowed
Install Intent State Passed
Flow duration check Passed
Initial Intent State Passed
Intial Flow State Failed
Initial Connectivity Check Passed
Link Down Passed
Link Down Passed
Link Down Intent State Passed
Link Down Flow State Failed
Link Down Topology State Passed
Link Down Connectivity Check Passed
Isolation link Down Passed
Partial failure isolation link Down Intent State Failed
Partial failure isolation link Down Flow State Failed
Partial failure isolation link Down Topology State Passed
Partial failure isolation link Down Connectivity Check Passed
Partial failure isolation link Down Connectivity Check Failed
Link Up Passed
Link Up Passed
Link Up Passed
Link Up Intent State Failed
Link Up Flow State Failed
Link Up Topology State Passed
Link Up Scapy Packet Recieved Failed

Remove Intents FailedAfter removing intents Flow State Failed

Up Scapy Packet Received Passed
Remove Intents PassedAfter removing intents Flow State Passed

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

3000.1 NOOPTION: Install and test single point to multi point intents - PASS
3000.2 IPV4: Install and test single point to multi point intents - PASS
3000.3 IPV4_2: Add single point to multi point intents - PASS
3000.4 VLAN: Add single point to multi point intents - PASS
3000.5 VLAN: Add single point to multi point intents - PASS

Case 4000: Multi To Single Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

This test case will test single point to multi point intents using 3 node(s) cluster; Different type of hosts will be tested in each step such as IPV4, Dual stack, VLAN etc; The test will use OF 1.3 OVS running in Mininet and compile intents using Flow Objectives

4000.1 NOOPTION: Add multi point to single point intents - PASS
4000.2 IPV4: Add multi point to single point intents - PASS
4000.3 IPV4_2: Add multi point to single point intents - PASS
4000.4 VLAN: Add multi point to single point intents - PASS
4000.5 VLAN: Add multi point to single point intents - PASS
4000.6 ENCAPSULATION: Add multi point to single point intents - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

5000.1 Testing host mobility by moving h1 from s5 to s6 - PASS
5000.2 IPV4: Add host intents between h1 and h9 - PASS

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.3 - Using Flow Objectives - PASS

6000.1 Installing Multi to Single Point intents with no options set - PASS
6000.2 Installing Multi to Single Point intents with partial failure allowed - PASS
6000.3 NOOPTION: Install and test single point to multi point intents - PASS
6000.4 NOOPTION: Install and test single point to multi point intents with partial failures allowed - PASS

Case 18: Stop Mininet and Scapy - PASS

...

Page tree

Page History

Versions Compared

Old Version 951

New Version 952

Key

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives -

PASS

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 18: Stop Mininet and Scapy - PASS

Case 19: Copy karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Case 10: Start Mininet topology with OF 1.0 switches - PASS

Case 12: Assign switches to controllers - PASS

Case 13: Create scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

Case 16: Balance mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

Case 18: Stop Mininet and Scapy - PASS

Case 19: Copy karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Case 10: Start Mininet topology with OF 1.0 switches - PASS

Case 12: Assign switches to controllers - PASS

Case 13: Create scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

Case 16: Balance mastership of switches - PASS

Case 17: Enable intent compilation using Flow Objectives - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - FAIL

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case

4000:

Multi To Single Point Intents Test - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.0 - Using Flow Objectives - PASS

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.0 - Using Flow Objectives -

FAIL

Case 18: Stop Mininet and Scapy - PASS

Case 19: Copy karaf logs - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Case 13: Create scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

Case 16: Balance mastership of switches - PASS

Case 1000: Host Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 2000: Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 3000: Single to Multi Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 4000: Multi To Single Point Intents Test - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

Case 5000: Test host mobility with host intents - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

Case 6000: Test Multi to Single End Point Failure - 1 NODE(S) - OF 1.3 - Using Flow Rules - FAIL

Case 18: Stop Mininet and Scapy - PASS

Case 19: Copy karaf logs - PASS

Case 2: Starting up 3 node(s) ONOS cluster - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Case 13: Create scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

Case 16: Balance mastership of switches - PASS

Case 1000: Host Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 2000: Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 3000: Single to Multi Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 4000: Multi To Single Point Intents Test - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 5000: Test host mobility with host intents - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 6000: Test Multi to Single End Point Failure - 3 NODE(S) - OF 1.3 - Using Flow Rules - PASS

Case 18: Stop Mininet and Scapy - PASS

Case 19: Copy karaf logs - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

Case 11: Start Mininet topology with OF 1.3 switches - PASS

Case 12: Assign switches to controllers - PASS

Case 13: Create scapy components - PASS

Case 15: Discover all hosts using scapy - PASS

Case

16:

Balance mastership of switches

- PASS

Case