Page History

...

• 1.1 Constructing test variables - PASS

Case 2: Starting up 1 node(s) ONOS cluster -

...

Set up ONOS with 1 node(s) ONOS cluster

• 2.1 Apply cell to environment - PASS
• 2.2 Uninstalling Atomix - PASS
• 2.3 Uninstalling ONOS package - PASS
• 2.4 Creating ONOS package - PASS
• 2.5 Installing Atomix - PASS
• 2.6 Installing ONOS package - PASS
• 2.7 Set up ONOS secure SSH - PASS
• 2.8 Checking ONOS service - PASS
• 2.9 Starting ONOS CLI sessions - PASS
• 2.10 Checking ONOS nodes - PASS
• 2.11 Checking ONOS applications - PASS

Case 10: Compare ONOS Topology view to Mininet topology - PASS

Compare topology elements between Mininet and ONOS

• 10.1 Setup Mininet Topology - PASS
• 10.2 Assign switch to controller - PASS
• 10.3 Comparing Mininet topology to ONOS topology - PASS

Case 11: Starting scapy with Mininet - PASS

• 11.1 Creating Host component - No Result
• 11.2 Start scapy components - PASS

Case 1000: Verify flow MAC selectors are correctly compiled - PASS

Install two flows with only MAC selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the MAC src and dst.

• 1000.1 Add flows with MAC addresses as the only selectors - PASS
• 1000.2 Check flow is in the ADDED state - PASS
• 1000.3 Check flows are in Mininet's flow table - PASS
• 1000.4 Send a packet to verify the flows are correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1100: Verify VLAN selector is correctly compiled - PASS

Install one flow with only the VLAN selector specified, then verify the flow is added in ONOS, and finally broadcast a packet with the correct VLAN tag.

• 1100.1 Add a flow with the VLAN tag as the only selector - PASS
• 1100.2 Check flow is in the ADDED state - PASS
• 1100.3 Check flows are in Mininet's flow table - PASS
• 1100.4 Send a packet to verify the flow are correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1200: Verify flow IP selectors are correctly compiled - PASS

Install two flows with only IP selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the IP src and dst.

• 1200.1 Add flows with ARP addresses as the only selectors - PASS
• 1200.2 Check flow is in the ADDED state - PASS
• 1200.3 Check flows are in Mininet's flow table - PASS
• 1200.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1300: Verify the MPLS selector is correctly compiled on the flow. - PASS

Install one flow with an MPLS selector, verify the flow is added in ONOS, and finally send a packet via scapy that has a MPLS label.

• 1300.1 Add a flow with a MPLS selector - PASS
• 1300.2 Check flow is in the ADDED state - PASS
• 1300.3 Check flows are in Mininet's flow table - PASS
• 1300.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1400: Verify flow IP selectors are correctly compiled - PASS

Install two flows with only IP selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the IP src and dst.

• 1400.1 Add flows with IPv4 addresses as the only selectors - PASS
• 1400.2 Check flow is in the ADDED state - PASS
• 1400.3 Check flows are in Mininet's flow table - PASS
• 1400.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1500: Verify IPv6 selector is correctly compiled - PASS

Install two flows with only IP selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the IP src and dst.

• 1500.1 Add flows with IPv6 addresses as the only selectors - PASS
• 1500.2 Check flow is in the ADDED state - PASS
• 1500.3 Check flows are in Mininet's flow table - PASS
• 1500.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1600: Verify the UDP selector is correctly compiled on the flow - PASS

Install a flow with only the UDP selector specified, verify the flow is added in ONOS, and finally send a UDP packet to verify the UDP selector is compiled correctly.

• 1600.1 Add a flow with a UDP selector - PASS
• 1600.2 Check flow is in the ADDED state - PASS
• 1600.3 Check flows are in Mininet's flow table - PASS
• 1600.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1700: Verify the TCP selector is correctly compiled on the flow - PASS

Install a flow with only the TCP selector specified, verify the flow is added in ONOS, and finally send a TCP packet to verify the TCP selector is compiled correctly.

• 1700.1 Add a flow with a TCP selector - PASS
• 1700.2 Check flow is in the ADDED state - PASS
• 1700.3 Check flows are in Mininet's flow table - PASS
• 1700.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1800: Verify the UDP selector is correctly compiled on the flow - PASS

Install a flow with only the UDP selector specified, verify the flow is added in ONOS, and finally send a UDP packet to verify the UDP selector is compiled correctly.

• 1800.1 Add a flow with a SCTP selector - PASS
• 1800.2 Check flow is in the ADDED state - PASS
• 1800.3 Check flows are in Mininet's flow table - PASS
• 1800.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 1900: Verify the ICMPv4 selector is correctly compiled on the flow - PASS

Install a flow with only the ICMPv4 selector specified, verify the flow is added in ONOS, and finally send a IMCPv4 packet to verify the ICMPv4 selector is compiled correctly.

• 1900.1 Add a flow with a ICMPv4 selector - PASS
• 1900.2 Check flow is in the ADDED state - PASS
• 1900.3 Check flows are in Mininet's flow table - PASS
• 1900.4 Send a packet to verify the flow is correct - PASS

Case 3000: Delete flows that were added through rest - PASS

• 3000.1 Deleting flows - PASS

Case 2000: Verify the ICMPv6 selector is correctly compiled on the flow - PASS

Install a flow with only the ICMPv6 selector specified, verify the flow is added in ONOS, and finally send a IMCPv6 packet to verify the ICMPv6 selector is compiled correctly.

• 2000.1 Add a flow with a ICMPv6 selector - PASS
• 2000.2 Check flow is in the ADDED state - PASS
• 2000.3 Check flows are in Mininet's flow table - PASS
• 2000.4 Send a packet to verify the flow is correct - PASS

Case 12: Stop Mininet and Scapy - PASS

Stopping the current mininet topology to start up fresh

• 12.1 Stopping and Removing Scapy Host Components - PASS
• 12.2 Stopping Mininet - PASS

...

FAIL