1.6-FUNCflow

Case 1: Constructing test variables and building ONOS package - PASS

• 1.1 Constructing test variables - PASS

Case 2: Starting up 1 node(s) ONOS cluster - PASS

• 2.1 Apply cell to environment - PASS
• 2.2 Creating ONOS package - PASS
• 2.3 Uninstalling ONOS package - PASS
• 2.4 Installing ONOS package - PASS
• 2.5 Starting ONOS service - PASS
• 2.6 Start ONOS cli - PASS

Case 10: Setup mininet and compare ONOS topology view to Mininet topology - PASS

Start mininet with custom topology and compare topology elements between Mininet and ONOS

• 10.1 Setup Mininet Topology - PASS
• 10.2 Assign switch to controller - PASS
• 10.3 Comparing MN topology to ONOS topology - PASS

Case 1000: Verify flow MAC selectors are correctly compiled - PASS

Install two flows with only MAC selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the MAC src and dst.

• 1000.1 Add flows with MAC addresses as the only selectors - PASS
• 1000.2 Check flows are in the ADDED state - PASS
• 1000.3 Check flows are in Mininet's flow table - PASS
• 1000.4 Send a packet to verify the flows are correct - PASS

Case 2000: Delete flows that were added through rest - PASS

• 2000.1 Deleting flows - PASS

Case 1100: Verify flow IP selectors are correctly compiled - PASS

Install two flows with only IP selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the IP src and dst.

• 1100.1 Add flows with IPv4 addresses as the only selectors - PASS
• 1100.2 Check flow is in the ADDED state - PASS
• 1100.3 Check flows are in Mininet's flow table - PASS
• 1100.4 Send a packet to verify the flow is correct - PASS

Case 2000: Delete flows that were added through rest - PASS

• 2000.1 Deleting flows - PASS

Case 1200: Verify VLAN selector is correctly compiled - PASS

Install one flow with only the VLAN selector specified, then verify the flow is added in ONOS, and finally broadcast a packet with the correct VLAN tag.

• 1200.1 Add a flow with the VLAN tag as the only selector - PASS
• 1200.2 Check flows are in the ADDED state - PASS
• 1200.3 Check flows are in Mininet's flow table - PASS
• 1200.4 Send a packet to verify the flow are correct - PASS

Case 2000: Delete flows that were added through rest - PASS

• 2000.1 Deleting flows - PASS

Case 1300: Verify the MPLS selector is correctly compiled on the flow. - PASS

Install one flow with an MPLS selector, verify the flow is added in ONOS, and finally send a packet via scapy that has a MPLS label.

• 1300.1 Add a flow with a MPLS selector - PASS
• 1300.2 Check flow is in the ADDED state - PASS
• 1300.3 Check flows are in Mininet's flow table - PASS
• 1300.4 Send a packet to verify the flow is correct - PASS

Case 2000: Delete flows that were added through rest - PASS

• 2000.1 Deleting flows - PASS

Case 1400: Verify the TCP selector is correctly compiled on the flow - PASS

Install a flow with only the TCP selector specified, verify the flow is added in ONOS, and finally send a TCP packet to verify the TCP selector is compiled correctly.

• 1400.1 Add a flow with a TCP selector - PASS
• 1400.2 Check flow is in the ADDED state - PASS
• 1400.3 Check flows are in Mininet's flow table - PASS
• 1400.4 Send a packet to verify the flow is correct - PASS

Case 2000: Delete flows that were added through rest - PASS

• 2000.1 Deleting flows - PASS

Case 1500: Verify the UDP selector is correctly compiled on the flow - PASS

Install a flow with only the UDP selector specified, verify the flow is added in ONOS, and finally send a UDP packet to verify the UDP selector is compiled correctly.

• 1500.1 Add a flow with a UDP selector - PASS
• 1500.2 Check flow is in the ADDED state - PASS
• 1500.3 Check flows are in Mininet's flow table - PASS
• 1500.4 Send a packet to verify the flow is correct - PASS

Case 100: - PASS