Have questions? Stuck? Please check our FAQ for some common questions and answers.

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

FUNCflow at 06 Nov 2015 21:03:55

Case 1: Constructing test variables and building ONOS package - PASS

  • 1.1 Constructing test variables - PASS (tick)

Case 2: Starting up 1 node(s) ONOS cluster - PASS

  • 2.1 Apply cell to environment - PASS (tick)
  • 2.2 Creating ONOS package - PASS (tick)
  • 2.3 Uninstalling ONOS package - PASS (tick)
  • 2.4 Installing ONOS package - PASS (tick)
  • 2.5 Starting ONOS service - PASS (tick)
  • 2.6 Start ONOS cli - PASS (tick)

Case 10: Setup mininet and compare ONOS topology view to Mininet topology - PASS

Start mininet with custom topology and compare topology elements between Mininet and ONOS

  • 10.1 Setup Mininet Topology - PASS (tick)
  • 10.2 Assign switch to controller - PASS (tick)
  • 10.3 Conmparing MN topology to ONOS topology - PASS (tick)

Case 1000: Verify flow MAC selectors are correctly compiled - PASS

Install two flows with only MAC selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the MAC src and dst.

  • 1000.1 Add flows with MAC addresses as the only selectors - PASS (tick)
  • 1000.2 Check flows are in the ADDED state - PASS (tick)
  • 1000.3 Send a packet to verify the flows are correct - PASS (tick)

Case 2: Starting up 1 node(s) ONOS cluster - PASS

  • 2.1 Apply cell to environment - PASS (tick)
  • 2.2 Creating ONOS package - PASS (tick)
  • 2.3 Uninstalling ONOS package - PASS (tick)
  • 2.4 Installing ONOS package - PASS (tick)
  • 2.5 Starting ONOS service - PASS (tick)
  • 2.6 Start ONOS cli - PASS (tick)

Case 1100: Verify flow IP selectors are correctly compiled - PASS

Install two flows with only IP selectors specified, then verify flows are added in ONOS, finally send a packet that only specifies the IP src and dst.

  • 1100.1 Add flows with IPv4 addresses as the only selectors - PASS (tick)
  • 1100.2 Check flow is in the ADDED state - PASS (tick)
  • 1100.3 Send a packet to verify the flow is correct - PASS (tick)

Case 2: Starting up 1 node(s) ONOS cluster - PASS

  • 2.1 Apply cell to environment - PASS (tick)
  • 2.2 Creating ONOS package - PASS (tick)
  • 2.3 Uninstalling ONOS package - PASS (tick)
  • 2.4 Installing ONOS package - PASS (tick)
  • 2.5 Starting ONOS service - PASS (tick)
  • 2.6 Start ONOS cli - PASS (tick)

Case 1200: Verify VLAN selector is correctly compiled - PASS

Install one flow with only the VLAN selector specified, then verify the flow is added in ONOS, and finally broadcast a packet with the correct VLAN tag.

  • 1200.1 Add a flow with the VLAN tag as the only selector - PASS (tick)
  • 1200.2 Check flows are in the ADDED state - PASS (tick)
  • 1200.3 Send a packet to verify the flow are correct - PASS (tick)

Case 100: - PASS

  • No labels